# Whitish Finish on Parquet: Causes and Fix

> Diagnosing cloudiness and white marks on wood floors. Crazing of urea-formaldehyde finishes, screed moisture and our restoration protocol in Madrid.

URL: https://www.parksinta.com/en/blog/whitish-cloudy-parquet-finish-causes-fix/  

---

- [![Tarima maciza pino melis viejo con gran veladura urea 1024x768](https://www.parksinta.com/wp-content/uploads/2015/05/Tarima-maciza-pino-melis-viejo-con-gran-veladura-urea-1024x768.jpg.webp)](https://www.parksinta.com/wp-content/uploads/2015/05/Tarima-maciza-pino-melis-viejo-con-gran-veladura-urea-1024x768.jpg.webp)

When a wood floor loses its clarity and shows a whitish haze, the problem is rarely built-up dirt. Rubbing with waxes or household cleaners hides the defect for a few hours, but makes it worse, because the wax gets into the cracks in the finish. The first step is to see whether the change is on the surface or inside the film of the finish.

## Is the problem on top of the finish or inside it?

Before planning any work, it is worth doing a simple check in a corner that is not very visible. Wipe a cloth lightly dampened with clean warm water over the affected area and watch how it dries.

If the white mark disappears and does not come back when dry, it was on top of the finish: limescale or cleaning residue. If the surface stays cloudy and milky, the damage is inside the finish.

![Damero de tablillas con el barniz antiguo moteado de blanco](https://www.parksinta.com/wp-content/uploads/2015/05/Tarima-maciza-pino-melis-viejo-con-gran-veladura-urea-1024x768.jpg.webp)

*Source: ParkSinta technical archive. Checkerboard of strips with blocks at the corners: the old finish, speckled white along the grain.*

## Jobs in Madrid: cloudiness on oak, pitch pine and tropical woods

Loss of clarity looks different depending on the wood. On reddish woods like doussie the white haze stands out strongly; on oak or pitch pine the floor looks as if covered in fog and the grain can hardly be seen. Sometimes the white covers the whole room and other times it appears in scattered patches.

![Parquet de roble en espiga con el barniz velado de blanco en media habitación](https://www.parksinta.com/wp-content/uploads/2015/05/Parquet-roble-entreverado-pegado-gran-veladura-2-1024x768.jpg.webp)

*Source: ParkSinta technical archive. Herringbone oak with a clouded finish: the white covers half the room and the other half still shines.*

![Tarima de doussié con una mancha blanca en el barniz](https://www.parksinta.com/wp-content/uploads/2012/12/Dussie-mancha-blanca-veladura-urea-scaled-800x600.jpg.webp)

*Source: ParkSinta technical archive. Doussie with a white mark in the finish: it cannot be fixed with a floor polish.*

![Tarima tropical con el barniz antiguo blanquecino y levantado a trozos](https://www.parksinta.com/wp-content/uploads/2012/12/Tarima-tropical-blanco-urea-scaled-800x1067.jpg.webp)

*Source: ParkSinta technical archive. Tropical wood flooring with the old finish gone whitish and, at top right, peeling off in pieces.*

![Tarima en cesteado con filetes claros y manchas blancas en el barniz](https://www.parksinta.com/wp-content/uploads/2015/05/Tarima-maciza-veladura-urea-formol.jpg.webp)

*Source: ParkSinta technical archive. Basketweave flooring with light-colored fillets: scattered white marks in the finish, at top right.*

## The main cause in Madrid: rigidity and fine crazing of urea-formaldehyde

On floors finished before 2010 with an acid-catalyzed finish, the most likely cause is urea-formaldehyde (we explain it in [urea-formaldehyde at home and pregnancy](https://www.parksinta.com/en/blog/urea-formaldehyde-risks-wood-flooring-waterborne-alternatives/)). Urea-formaldehyde forms a very hard film, but one without the elasticity to follow the movements of the wood.

In winter, heating brings the relative humidity of Madrid homes below 30%. The wood shrinks and the rigid film crazes into hairline cracks that scatter the light: that is the white haze. Grease and mopping water then get through those cracks down to the wood, where they can no longer be cleaned.

## Other causes: finishing conditions, heat and harsh products

When the finish is not urea but polyurethane, white marks have other causes. If the white appears on a freshly applied finish, look at the conditions it was applied in. The data sheets call for 18 to 25 °C (Bona) or 18 to 22 °C (Deva), with relative humidity of 40 to 60% and never below 13 °C. Bona’s sheet warns that drying in poor conditions leaves a weak film with poor adhesion.

A portable heater or a hot container on the parquet softens the finish and leaves whitish rings when it cools. Regular use of cleaners with ammonia, bleach or strong degreasers attacks the surface of the finish and leaves it dull and rough.

## White marks and cloudiness: cause and fix

Knowing where the mark comes from avoids spending money on products that will not remove it. These are the cases we see most often on site and what is done in each.

| Appearance | Finish | Cause | Does cleaning remove it? | Fix |
| --- | --- | --- | --- | --- |
| White marks that go away with a damp cloth | Any | Limescale or cleaning residue on top of the finish | Yes | Clean with the manufacturer’s parquet cleaner |
| Milky white haze over the whole floor | Old urea-formaldehyde | Rigid film crazed by dryness | No (wax and grease make it worse) | Sand down to bare wood and apply a waterborne finish |
| Round whitish rings | Any finish | Heat from a heater or a container | No | If the finish is sound, abrade it and apply a new coat (see [recoating](https://www.parksinta.com/en/blog/recoating-parquet-without-sanding/)) |
| Gray or sticky film | Any floor | Layers of maintenance wax | It helps, but not enough | To refinish, sand down to bare wood: you cannot recoat over wax |

## ParkSinta’s workshop protocol for getting rid of cloudiness

If the urea film has crazed, the fix is to remove all the finish down to clean wood. Before quoting, we need to see whether the mark is on the surface, whether the finish is clouded, whether there is moisture and how much usable thickness is left for sanding.

With nailed solid flooring, below 2–3 mm of wood above the tongue restoration is hardly viable; with glued parquet, what counts is the visible wood layer above the base. We explain this in [how many times a parquet or wood floor can be sanded](https://www.parksinta.com/en/blog/how-many-times-sand-parquet-solid-wood-floor/). On a floating floor the wear layer is thin: a standard 14 mm engineered floor usually takes one sanding, and two with great care (see [can a floating floor be sanded?](https://www.parksinta.com/en/blog/can-you-sand-and-refinish-engineered-wood-floors/)).

The moisture content of the wood is measured with a moisture meter. If moisture rising from the screed is suspected, the screed is measured with the carbide method, chipping out the sample at 2–3 cm, and the limits are set by UNE 56810.

Then the floor is sanded with the grit sequence it needs, using machines with continuous extraction so the home does not fill with dust. With the wood clean, the finish is chosen (see [parquet finishes](https://www.parksinta.com/en/wood-floor-finishes-madrid/) and [gloss, satin or matte](https://www.parksinta.com/en/blog/parquet-finish-gloss-satin-matte/)). The finish is three or more coats of waterborne polyurethane, and the first can be a primer coat that blocks the tannins in the wood.

## Prevention

To keep it from happening again, avoid mopping with too much water, harsh products, incompatible waxes and partial repairs on old finishes without a test first. For daily cleaning a dust mop is enough and, for wet cleaning, a well-wrung mop with the manufacturer’s parquet cleaner, as the Bona and Deva data sheets require.

Waterborne finishes yellow less than the old ones and have little odor, though the room must be ventilated while they dry (see [waterborne versus solvent-based finish](https://www.parksinta.com/en/blog/waterborne-polyurethane-finish-vs-traditional-varnish/)). Also, if the finish is still sound and free of wax, they can take a new coat later on without sanding (see [recoating parquet or wood flooring](https://www.parksinta.com/en/blog/recoating-parquet-without-sanding/)).

### Frequently asked questions

**Can a white haze be hidden by applying a coat of wax or oil?**

It is not recommended. Wax gets into the cracks in the finish, stains the wood and complicates finishing later: over wax or oil, the whole surface has to be sanded to go back to a finish.

**Can a coat of finish be applied on top to restore its clarity?**

It depends on where the white is. If it comes from a crazed urea finish, no: the new coat does not cover the cracks underneath, and we do not recoat over urea-formaldehyde, so the floor has to be sanded. If it is a heat ring on a sound waterborne finish, the surface is buffed and cleaned of contaminants and a new coat is applied, without sanding.

**Does old crazed urea-formaldehyde release formaldehyde into the air?**

It releases less over the years, but it does not stop, and it releases more with heat and humidity. There is no general figure: only an air measurement tells you how much. With a pregnancy or children it is advisable to remove it; we explain this, with its sources, in [urea-formaldehyde at home and pregnancy](https://www.parksinta.com/en/blog/urea-formaldehyde-risks-wood-flooring-waterborne-alternatives/).

**What should you do if bubbles appear in a freshly applied finish?**

Let the coat dry, abrade the area with light sanding and apply it again. Beforehand, let the mix stand for 5 to 10 minutes, as Deva’s data sheet requires. To keep them from coming back: the right roller, even passes keeping a wet edge, and the temperature and humidity on the data sheet. Outside those, according to Bona’s data sheet, the film is weak and bonds poorly.

Diagnosing cloudiness and restoring parquet in Madrid

At ParkSinta we look at the floor before quoting: where the white comes from, whether the finish is sound and how much wood is left to sand. Other finish failures, with photos from jobs, are in the [parquet chamber of horrors](https://www.parksinta.com/en/blog/parquet-wood-floor-horror-museum-real-mistakes/). If you are comparing renovation quotes, you can check the [VAT rate that applies](https://www.parksinta.com/blog/iva-10-o-iva-al-21/) to parquet restoration.

[Assessment and Sanding in Madrid](https://www.parksinta.com/en/hardwood-floor-sanding-madrid/)
 [📞 +34 91 543 90 62](tel:+34915439062)
 [Book an appointment in Chamberí (Donoso Cortés 24)](https://www.parksinta.com/en/contact/)
