# The Hardest Finish for Parquet and Wood Flooring

> Analysis of the most durable finishes for wood floors: Bona Traffic HD and Aquadeva Transit Plus compared, the Taber test and spread rate on site.

URL: https://www.parksinta.com/en/blog/most-durable-finish-parquet-wood-floors/  

---

- [![Bona Traffic HD Satinado 1200x600](https://www.parksinta.com/wp-content/uploads/2019/07/Bona-Traffic-HD-Satinado-1200x600.jpg.webp)](https://www.parksinta.com/wp-content/uploads/2019/07/Bona-Traffic-HD-Satinado-1200x600.jpg.webp)

The most durable finish for parquet or wood flooring is, in short, a professional-grade two-component (2K) waterborne polyurethane, applied well over well-prepared wood. The ones we apply are Bona Traffic HD and Aquadeva Transit Plus, from Deva, in heavily used homes and in professional spaces.

The long answer matters more: no finish makes a floor indestructible. The final durability depends on the whole system: wood, sanding, vacuuming, primer, number of coats, spread rate, drying times, room humidity and maintenance.

![Pasillo entre butacas de un salón de actos con parquet de roble barnizado en satinado](https://www.parksinta.com/wp-content/uploads/2019/07/Bona-Traffic-HD-Satinado-1200x600.jpg.webp)

*Source: ParkSinta technical archive. Aisle of an assembly hall: oak parquet with a satin finish, in an area of constant foot traffic.*

## What it means for a finish to be “hard”

In parquet, “hard” is often misused. A finish can stand up well to wear, scratching, rubber marks, water or certain chemicals. Each of those properties is measured in a different way. The hardness of the wood, for example, does not come from the finish: it is measured on the [Brinell scale](https://www.parksinta.com/blog/escala-de-la-dureza-de-las-maderas-escala-brinell-2/).

Before comparing data sheets, it is worth separating what each thing assesses:

| Question | What it assesses |
| --- | --- |
| **Wear (abrasion)** | The film lost through repeated rubbing. It is the figure closest to the wear of daily foot traffic. |
| **Scratching** | How the film stands up to dragging, sand, furniture legs, wheels or rubber marks. It does not always match wear. |
| **Friction** | The grip or slip underfoot. It matters for safety, but it does not measure the hardness or wear of the finish. Bona, for example, states that Traffic HD meets EN 14904 for friction on sports floors. |
| **Elasticity and impact** | Whether the film follows the movement of the wood and takes a blow without cracking. EN 13696 brings together test methods for elasticity, wear and impact for wood floors. |
| **Chemical resistance** | How the film responds to water, coffee, wine, cleaners, alcohol, rubber or marker pen. |
| **Hardness of the wood** | Resistance to indentation or denting. It depends on the species and the base, not on the finish. |

Elasticity matters in Madrid. In winter, with the heating on, the humidity of the air in homes drops below 30% and the wood shrinks. The film has to follow that movement without cracking or coming loose.

## Bona Traffic HD and Aquadeva Transit Plus

Bona Traffic HD is a two-component waterborne polyurethane finish designed for heavily used floors. Its [data sheet in Spanish](https://www.parksinta.com/wp-content/uploads/2016/01/Ficha-tecnica-de-producto-Bona-Traffic-HD-040215_es.pdf), from November 2014, gives around 32% solids and a maximum of 52 g/l of VOC, hardener included. It has the EC1R Plus emissions classification and little odor, and Bona recommends it for shops and public places that have to be back in use soon.

Aquadeva Transit Plus, from Deva, is also a two-component waterborne polyurethane. Its [data sheet (revision 15, May 2021)](https://quideva.com/wp-content/uploads/2023/02/Aquadeva-Transit-Plus.-rev15.pdf) describes it as a “100% polyurethane finish,” with 29–31% solids. It is mixed 10 parts finish to 1 part hardener. Deva specifies it for wood floors in commercial areas and places that need high wear resistance.

On wear, the two data sheets publish figures measured with different methods. That is why they cannot be used to decide which of the two finishes wins by a decimal point, even though they call for the same spread rate per coat.

## The figures from the two data sheets

Choosing does not take a huge table: a few figures read carefully are enough, such as the mix, the amount per coat, the times before use and the site conditions. If any of them fails, the finish does not reach the durability its data sheet promises.

| Figure | Bona Traffic HD | Aquadeva Transit Plus |
| --- | --- | --- |
| **Type** | Two-component waterborne polyurethane | Two-component waterborne finish, “100% polyurethane” |
| **Solids** | Around 32% | 29–31 % |
| **Mix** | 1 part hardener per liter of finish (8% by volume) | 10 parts finish to 1 part hardener; let stand 5–10 minutes |
| **Pot life** | 4 hours at 20 °C, less in warmer conditions | 3 hours |
| **Coverage per coat** | 8–10 m²/l (100–120 g/m²) | 8–10 m²/l (100–120 g/m²) |
| **Sanding between coats** | If needed, with a screen or 150-grit or finer sandpaper; always, if the previous coat is more than 24 hours old | With 180-grit sandpaper before the next coat; mandatory if the previous one is more than 24 hours old |
| **Drying and use** | Next coat or sanding: 2–3 hours. Light traffic: about 8 hours. Full use: 12 hours. Rugs: 3 days | Touch dry: 3–4 hours. Sanding: 6–8 hours. Moderate traffic: 24 hours, though it advises 1–2 days without walking on it. Maximum hardness: 8–10 days. Rugs and protectors: 1 week. Wet mopping: 2 weeks |
| **Application conditions** | 18–25 °C and 40–60% relative humidity; minimum 13 °C | 18–22 °C and 40–60% relative humidity; never below 13 °C; wood below 18–20% moisture content |
| **Sheen on the data sheet** | At 60°: satin ≈40%, matte ≈20% and extra matte ≈11% | Gloss ≈90; satin 57.5 ± 2.5; matte 27.5 ± 2.5; super matte 12.5 ± 2.5 (angle not stated) |
| **Emissions** | 52 g/l of VOC maximum; EC1R Plus classification | Within the VOC limits of Directive 2004/42/EC |

The practical reading is simple: both are professional-grade two-component waterborne finishes and call for the same spread rate. According to their data sheets, Bona can be used sooner, and Aquadeva asks for more time before rugs, protectors and wet cleaning.

These are manufacturer times, measured at 20 °C and around 60% relative humidity. On our jobs we leave at least 4–5 hours between intermediate coats, more if it needs buffing again. The last coat takes 12 to 24 hours before it can be walked on, depending on the product and the conditions.

## How the Taber test works and why its figures cannot be compared

The Taber test measures abrasion wear. A finished sample is weighed, turned under abrasive wheels with a fixed load for a number of revolutions and weighed again. The difference is the mass loss: the lower it is, the better that finish resists abrasion within that protocol.

The problem comes when comparing data sheets. A wear figure only makes sense with its protocol: type of wheel, load, number of revolutions, conditioning of the sample and preparation of the film.

That is what happens with these two finishes. The Bona Traffic HD data sheet gives 1–2 mg loss per 100 revolutions under the SIS 923509 method. The Aquadeva Transit Plus sheet gives 360 mg loss over 500 revolutions under UNE 4250:1992. Both figures are about wear, but one cannot be converted into the other or put in the same row of a table.

EN 13696 sets out test methods for wear, elasticity and impact for wood floors, but it does not make each brand’s commercial figures equivalent. If a data sheet does not say which wheel, which load and how many revolutions it used, its figure serves as a guide, not for ranking finishes.

Chemical resistance is measured another way, with EN 13442. According to [the CATAS laboratory](https://catas.com/en/news/wood-flooring-wood-panelling-and-cladding-resistance-to-chemical-agents/), its 2023 revision separates finishes with a continuous film of 20 microns or more from those that do not form one, such as oils and waxes. Each group has its own procedures and contact times, so an oil and a varnish do not go through the same test. Nor does the standard set a minimum to meet or a classification of results.

## Asking for “the hardest” and neglecting the work

A good finish applied over dust, moisture, grease, wax residue or a poor primer can fail. It also turns out worse if too little product is applied or if the floor is used too soon. When adhesion fails, the theoretical hardness of the finish no longer matters.

![Barniz de poliuretano al disolvente arrugado y levantado sobre una tabla de madera](https://www.parksinta.com/wp-content/uploads/2016/02/Descamaci%C3%B3n-Barniz-Poliuretano-Disolvente-1200x675.jpg.webp)

*Source: ParkSinta technical archive. Peeling of a solvent-based polyurethane finish: the film wrinkles and lifts off the board.*

The data sheets say it in their own way. Bona asks for a well-sanded, dry floor free of dust, oils and waxes, and warns that poor drying leaves a weakened film with poor adhesion. Nor does it recommend more than two full coats a day, because the wood can swell too much and cup.

Deva asks for the wood to be below 18–20% moisture content. A floor treated with waxes, oils, urea finishes or polishes cannot be recoated with its product without first sanding it down to the wood. On site we do the same: a floor with oil or wax is sanded completely before switching to varnish. When a recoat is enough we explain in [recoating parquet or wood flooring](https://www.parksinta.com/en/blog/recoating-parquet-without-sanding/).

## When to choose a high-durability finish

It makes sense in homes with children, dogs, office chairs on casters or open kitchens, and in entrances, shops, offices, waiting rooms or common areas of residential buildings. Also when the aim is to reduce maintenance and it is accepted that the floor will carry a visible protective film.

![Parquet de roble barnizado al agua 2K en el vestíbulo del Hotel Madrid EDITION, junto a una mesa de billar](https://www.parksinta.com/wp-content/uploads/2024/04/Hotel-Madrid-Edition-Lobby-parksinta-3-1.webp)

*Source: ParkSinta technical archive. The Madrid EDITION hotel: oak parquet in the lobby, with a 2K waterborne finish, in an area of constant foot traffic.*

For homes with quiet use and little traffic, a professional-grade one-component (1K) finish gives enough protection. On our jobs we apply both types of finish, 2K and 1K, and also oils.

A high-durability finish is not always the best choice if you want a very natural look, easy local repair or aging similar to that of oil. For the first there are natural and ultra-matte versions of the same 2K finishes, such as Deva Transit Plus Natur and Bona Traffic HD Raw; for the rest, an oil is worth considering.

The differences in sheen, feel and look are in the guide to [gloss, satin, matte and ultra-matte](https://www.parksinta.com/en/blog/parquet-finish-gloss-satin-matte/). If the question is water or solvent, the article on [waterborne finish versus traditional finishes](https://www.parksinta.com/en/blog/waterborne-polyurethane-finish-vs-traditional-varnish/) answers it. The finishes we apply are on [parquet finishes](https://www.parksinta.com/en/wood-floor-finishes-madrid/).

## How to avoid scratches at home

The finish improves the resistance of the surface, but it does not remove the need for maintenance. To reduce scratches, very specific measures matter:

- **Doormats at the entrance**, so that sand from the street stays outside.
- **Felt pads or protectors on the legs** of chairs, tables and beds.
- **Suitable casters** on desk chairs and furniture on wheels.
- **Cleaning without grit**: remove dust with a mop and wash with a well-wrung mop and a cleaner made for parquet, as the Deva data sheet asks.
- **Do not drag furniture**: lift it to move it.

Something similar happens with stains: one cleaned quickly leaves less of a mark than one left to dry. And during curing the floor needs more care, with no rugs or heavy furniture until the days set by each finish’s data sheet have passed.

## Which finish we recommend

For a heavily used home or a commercial space, we recommend a professional-grade two-component waterborne finish, applied by a team that controls every step. Bona Traffic HD and Aquadeva Transit Plus are two reasonable options.

If the floor is badly worn or has stains, moisture, old waxes or incompatible finishes, the base has to be looked at first. The finish matters, but the decision starts earlier: whether to [sand and refinish](https://www.parksinta.com/en/hardwood-floor-sanding-madrid/), repair pieces, change the system or consider another finish.

### Frequently asked questions

**Does a very hard finish prevent heel marks?**

No. Heel and impact marks are dents in the wood and depend on its hardness, which is measured on the Brinell scale. The finish film protects against wear, scratching and stains, not against impacts.

**How many coats of finish does a full restoration take?**

In our restorations, three coats or more; the first can be a primer. The Bona Traffic HD data sheet, over untreated wood, calls for a waterborne primer, a light sanding at 150 grit and two coats of finish.

**When can you walk on the floor and put back rugs and furniture?**

On our jobs, the last coat takes 12 to 24 hours before it can be walked on, depending on the product and the conditions. For rugs and furniture, each finish’s data sheet sets the rule. Bona Traffic HD asks for at least 3 days without rugs or heavy objects; Aquadeva Transit Plus, a week before putting down rugs and protectors.

High-durability finishing in Madrid

Before choosing the finish we look at the floor on site: what wood it is, what finish it has and what use it will get. A similar case: [High-Traffic Lobby Parquet Rehabilitation – The Madrid EDITION Hotel](https://www.parksinta.com/en/projects/hotel-madrid-edition-high-traffic-lobby-parquet/).

[Parquet restoration and sanding](https://www.parksinta.com/en/hardwood-floor-sanding-madrid/)
 [📞 +34 91 543 90 62](tel:+34915439062)
 [Book an appointment in Chamberí (Donoso Cortés 24)](https://www.parksinta.com/en/contact/)
